Thin-Walled Pipe Welding Challenges — How Walhonde Tools Benefit These Jobs

Thin-Walled Pipe Welding Challenges — How Walhonde Tools Benefit These Jobs

Working with thin-walled pipe can be time-consuming. Welding thin piping, such as Schedule 10 pipe, is especially challenging when it often arrives out of round and distorted. Standard fit-ups for these pipes can take hours per joint when using traditional methods. However, even when using wedges and standard clamps, you may still be unable to correct the shape to meet alignment tolerances. 

Walhonde Tools solves these issues with high-quality pipe alignment tools that can round distorted pipes and significantly reduce alignment time. Read on to learn how to eliminate high points and satisfy alignment tolerances. 

Key Challenges of Welding Thin Tubing and Pipe

In heavy industrial construction, thin-walled pipe is an essential material. However, it can be difficult to work with due to its lack of rigidity. This often means thin piping, like Schedule 10, sags during transport, resulting in an oval or egg-shaped profile. A thin-walled pipe can also distort with waviness along its edge.

These issues make it challenging to meet the standards set by the American Society of Mechanical Engineers (ASME) for alignment tolerances, such as ASME B31.3. Even the slightest degree of out-of-roundness can create a rejectable high-low mismatch. 

For NPS 24 and smaller pipe ends, the standard limits internal misalignment to just about 0.06 inch. Achieving the right alignment ensures your weld passes inspections and meets industry standards. This saves you considerable time by eliminating the need to rework rejected welds. 

Why Traditional Tools Fail Manufacturing Standards

Traditionally, welders use standard chain or cage clamps for joining thin pipes. These clamps are only designed to hold the pipe. Typically, with thin-walled pipe, the clamps will conform to the existing oval shape. This usually then requires time and manual labor to reform. Using wedges, hammers and come-alongs, these traditional methods force the pipe around inch by inch. 

Schedule 10 pipe can also become wavy due to heat treatment after cutting. Traditional tools, like standard rounding clamps, fail here because — while they can correct the out-of-roundness — they still cannot adjust the edge profile. 

When working on large-scale construction or manufacturing projects, you may have hundreds of pipe fittings to reform. Schedule 10 doesn't respond well to more traditional, brute force alignment methods. These methods can damage the workpiece before you even begin welding. These risks delay projects and waste materials.

If a weld fails inspection due to poor axial alignment and gapping, it can significantly increase the project's costs. It isn't just the impact of rewelding, but also the cutting, re-beveling and any further testing. 

How Top Liners Solve the Thin-Walled Pipe Rounding Problem

Top Liners are pipe alignment tools that reform any out-of-roundness while providing all-around weld nozzle access to the joint. They differ from traditional tools in that they offer precise capabilities to align the pipe.

How Top Liners Solve the Thin-Walled Pipe Rounding Problem

Designed with an open structure, welders can access the whole joint for tacking or pre-heating without having to remove the Top Liner. Traditional full-cage clamps block part of the joint, which requires you to move the tool. By keeping the Top Liner in place, you prevent the pipes from slipping. 

Walhonde has a range of Top Liners to fit pipes from 2" to 72". We designed our Top Liner Gen III for light-to-medium duty pipes, including thin-walled Schedule 10 applications where minimal preload is needed. The Top Liner Gen III is more versatile than the original, as it can align pipes to pipes, elbows, tees or flanges with either a short or long radius. 

The external rings of the Top Liner actively force the pipe into a perfect circle as the tool tightens. This corrects the egg shape in a thin-walled pipe. Top Liners are easy to use, and when used correctly, there's no need for any external dogs or wedges. Once you train an operator to use the Top Liner correctly, they can achieve repeatability with an accurate, precise process. 

Another benefit of Top Liner from Walhonde Tools is increased safety and ergonomics. Once you've set your Top Liner to align pipes, there's no further manual labor needed. In comparison, brute force methods can pose injury risks from pinched fingers or flying metal from using hammers or come-alongs. 

Top Liners also help constrain the stresses and tension from fitting pipes. These tools are also more ergonomic, as they minimize physical labor for welders, which can help sustain weld quality over longer shifts. 

Eliminating High Points With Fine Tuner Bars

Our Fine Tuner bars can handle high points or divots in your thin-walled pipe. With stainless steel pads on each end, you can drive down any high points or divots to make the surface more rounded and eliminate issues with setting the correct gap. This ensures you can achieve a consistent weld gap around the joint. By using the Fine Tuner bar, you also avoid contaminating the pipe material with rust.

With the push-pull mechanism of the Fine Tuner Bar, you can target the high point precisely without deforming the surrounding pipe. 

Case Study: PCL Texas Cuts Fit-Up Time from 5 Hours to 35 Minutes

PCL Industrial Construction Co. in Texas needed to align a large quantity of thin-walled pipes, ranging from 8" to 32". Many of these pipes were Schedule 10, which typically required four to five hours to align and set the gaps correctly. 

By switching to Walhonde Tools, PCL was able to align the pipes in 35 minutes. This huge time and labor-saving compound occurs when you have a project with hundreds of fittings. With the Top Liner and Fine Tuner bars, you can make thin-walled pipe much easier to work with and complete projects more efficiently. 

Rent Thin-Walled Pipe Tools

Walhonde Tools offers a rental program that allows you to access specialized tooling for thin-walled pipes, even for one-off projects. You can rent multiple sizes of Top Liners at one time for your project. This provides a low-risk opportunity to experience the efficiency gains firsthand before committing to purchasing a tool outright. Our inventory has the specific stock you need to tackle thin-wall projects immediately. 

By renting with us, you can maximize the efficiency of your capital by cycling tools. You can rent the tools as you need for each stage of your project. This keeps your tooling costs down and focused on tools you're actively using rather than just sitting in your warehouse. 

Why Trust Us With Your Critical Alignment Needs

Since 1986, Walhonde Tools has designed and manufactured precision tube and pipe alignment solutions. Our solutions are the trusted choice for many industries, from energy to aerospace, where precision is nonnegotiable. 

By choosing us, you get high-quality, US-manufactured tools that deliver results in minutes, not hours. If you need a specific size tool, we offer custom solutions to meet your demands. We stand by our tools and want our customers to get the best results, so we offer on-site training. 

Build Faster, Smarter and Safer With Walhonde Tools

Build Faster, Smarter and Safer With Walhonde Tools

While Schedule 10 pipe can be fragile and hard to align, the right tools can help you complete the job in minutes rather than hours. Unlike traditional methods, utilizing innovative solutions from Walhonde Tools enables you to achieve high-quality joins in a fraction of the time. 

Contact Walhonde Tools to request a free consultation and solve thin-walled pipe fitting problems quickly.

Back to blog